Oracle X5-4 Скачать руководство пользователя страница 32

Страница: 32 / 358

Server Subsystems Overview

Slot 2 is reserved for the HBA that can support up to six SAS/SATA (mechanical or SSD)

drives in all six drive slots.

Slot 1 can be used for a factory option PCIe NVMe Switch Card that can support up to four

NVMe SSDs in drive slots 2 through 5.

Note -

The NVMe Switch card is only supported in PCIe slot 1 and will not work in other PCIe

slots.

For slot designation information, see

“PCIe Slot Designations” on page 77

Two Internal and Four External High-Speed USB Ports

The two internal USB ports are located on the motherboard between the disk drive backplane

and the PSU backplane boards. These ports can take a standard USB flash device, which can

be used for system booting. Your system might be equipped with a preinstalled Oracle System

Assistant USB device.

The Oracle System Assistant provides a separately bootable device that aids in the installation

of the primary host OS, server hardware configuration, and the firmware upgrade process. Do

not use the Oracle System Assistant USB drive as the primary host boot device or as server

storage. If installed in your server, the Oracle System Assistant USB drive must be installed in

the port labeled "OSA USB."

For port designations, see

“DVD, Storage Drive, and USB Designations” on page 78

Additionally, the server has four external USB ports, two on the front panel and two on the back

panel. See

“External Components and Features” on page 17

Four Onboard 10GbE Ports

Four 10 GigabitEthernet ports are located on the back panel of the server (see

“Back Panel

Connector Locations” on page 60

). From left to right, the two bottom ports are NET 0 and

NET 1; the two top ports are NET2 and NET 3, as shown in the following illustration.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды