Oracle X5-4 Скачать руководство пользователя страница 96

Страница: 96 / 358

Prepare the Server for Cold Service

Remove the power cord retainer clips by lifting them up to disengage them from

the power cords.

Remove both server power cords.

Caution -

Data loss. Removing the power cords when the server is in full power mode results

in an immediate shut down of the server. Do not remove the power cords if the server is in full

power mode.

To slide the server out of the rack to the maintenance position, do the following:

Most component service procedures can be performed without removing the server entirely

from the rack. Instead, the server can be slid out of the rack on its support rails to an extended

and locked position called the maintenance position.

At the back of the server, verify that the cables have sufficient length

and clearance to extend the server to the maintenance position without

damaging or overextending the cables.

The cable management arm (CMA) that is supplied with the server is hinged to facilitate

extending the server to the maintenance position. Ensure the sliding movement does not

impede or damage the cables. If necessary, label and remove cables from the back of the

server.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды