Oracle X5-4 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 358

background image

Servicing PCIe Cards

135 Sun May 21 00:53:57 2000 DIMM Service Required Memory P0/MR0/D9 (CPU
Memory Riser 0 DIMM 9)
A failure has occurred during Memory Reference Code (MRC) DIMM module
training. (Probability:100, UUID:2a182715-983f-c4fb-e94f-b5a5b50d3650, Part
Number:001-0003-01,HMT42GR7AFR4A-PB, Serial Number:00AD011321345849FF,
Reference Document:http://support.oracle.com/msg/SPX86A-8004-67)

126 Sun May 21 00:53:56 2000 DIMM Service Required Memory P0/MR0/D6 (CPU
Memory Riser 0 DIMM 6)
A failure has occurred during Memory Reference Code (MRC) DIMM module
training. (Probability:33, UUID:9014a82c-7bf9-ee96-b61b-9c7ccedc9aed, Part
Number:001-0003-01,HMT42GR7AFR4A-PB, Serial Number:00AD01132129B11E9E,
Reference Document:http://support.oracle.com/msg/SPX86A-8004-67)

In this scenario, the DIMM in D6 failed at 00:53:56, and that failure is subsequently followed

by a reported failure of the DIMM in D9, which failed at 00:53:57. Both DIMMs are on the

same memory riser card (P0/MR0). Each DIMM is on a separate channel, but both are linked

to the same memory buffer ASIC. Additionally, all of the DIMMs in both channels might have

been disabled by the system. This scenario could be an instance of a multi-DIMM failure state.

How to Troubleshoot a Multi-DIMM Failure State

To troubleshoot this issue, replace only the DIMM that logged the initial failure and return the

server to operation to see if the multi-DIMM failure state persists. If a multi-DIMM failure state

had occurred, replacing only the DIMM that failed initially would rectify the fault state of the

initial DIMMs and the subsequent DIMMs. If the failures persists, the issue could be with the

DIMMs or with the memory riser card.

Servicing PCIe Cards

This section provides procedures for removing and installing PCIe cards and PCIe card filler

panels.

■

“Remove a PCIe Card” on page 161

■

“Install a PCIe Card” on page 164

■

“PCIe Slot Reference” on page 167

Note -

The factory installed Oracle Storage 12 Gb/s SAS RAID PCIe HBA (Internal) and

Oracle NVMe Switch PCIe card are only serviceable by Oracle Service personnel, see

“Servicing the Factory Installed SAS 12 Gb/s Internal HBA and ESM” on page 200

“Servicing the Factory Installed PCIe NVMe Switch Card” on page 212

.

160

Oracle Server X5-4 Service Manual • December 2015

«
...
158
159
160
161
162
...
»

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

eServer BladeCenter JS20 Type 8842

Бренд: IBM Страницы: 150

Бренд: Avaya Страницы: 19

Бренд: SEH Страницы: 5

SuperServer 5013C-MT

Бренд: Supero Страницы: 98

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

Бренд: TP-Link Страницы: 16

301300U - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 62

BACnet/IP Server-SUNWAYS

Бренд: IntesisBox Страницы: 5

Бренд: PRIMERGY Страницы: 87

Бренд: MISUMI Страницы: 18

FusionServer XH321 V5

Бренд: xFusion Digital Technologies Страницы: 76

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 155

NetStorage 6000

Бренд: HP Страницы: 192

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 44

PRIMERGY RX200 S6

Бренд: Fujitsu Страницы: 84

@server x Series

Бренд: IBM Страницы: 8

T19 Hydro Server

Бренд: BITMAIN Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды