manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 54

Troubleshooting Hardware Faults Using Oracle ILOM

Action

: Investigate the cause of the over-temperature event, and replace failed components

immediately

. For hardware troubleshooting information, see 

“Troubleshooting Server Hardware

Component Faults” on page 37

.

Prevention

: Component redundancy is provided to a allow for component failure in critical

subsystems, such as the cooling subsystem. However, once a component in a redundant

system fails, the redundancy no longer exists, and the risk for server shutdown and component

failures increases. Therefore, it is important to maintain redundant systems and replace failed

components 

immediately

.

Troubleshooting Power Issues

If your server does not power on, the cause of the problem might be one of the following:

■

“AC Power Connection” on page 54

■

“Power Supplies (PSUs)” on page 55

■

“Top Cover” on page 56

AC Power Connection

The AC power cords are the direct connection between the server power supplies and the power

sources. The server power supplies need separate stable AC circuits. Insufficient voltage levels

or fluctuations in power can cause server power problems. The power supplies are designed to

operate at a particular voltage and within an acceptable range of voltage fluctuations (see the

Installation Guide

). A four-CPU configured server needs to operate at 200-240 VAC, while

a two-CPU configured server can operate at either 100-127 VAC or 200-240 VAC. For more

information about the processor subsystem, see 

“Processor Subsystem” on page 22

.

Action

: Check that both AC power cords are connected to the server and check that the correct

power is present at the outlets. If necessary, monitor the power to verify that it is within the

54

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды