Oracle X5-4 Скачать руководство пользователя страница 248

Страница: 248 / 358

Replace the Motherboard (FRU)

To replace the motherboard, remove and retain internal motherboard-mounted components.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

To complete this procedure, you need:

■

Alcohol wipes

■

Thermal compound

Prepare the server for service.

See

“Prepare the Server for Cold Service” on page 94

Remove the SP card.

See

“Remove the SP Card (FRU)” on page 244

Remove all PCIe cards from the server, disconnecting any external or internal

cables and taking care to note their cable arrangement and slot assignments.

See

“Remove a PCIe Card” on page 161

The slot population on the replacement motherboard needs to match the population on the failed

board.

If the server has only two CPUs, remove the air baffle.

The air baffle simply lifts straight up and out of the system. It is not attached to anything.

Remove all memory riser cards.

See

“Remove a Memory Riser Card” on page 145

Disconnect the fan board power and data cables from motherboard.

248

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды