Oracle X5-4 Скачать руководство пользователя страница 133

Страница: 133 / 358

Install a Fan Module

Install a Fan Module

This procedure describes how to install a replacement fan module in the server.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For fan module designation information, see

“Component Designations” on page 73

■

For instructions on removing a fan, see

“Remove a Fan Module” on page 130

If you are installing a replacement fan module for one that has failed, check the

indicator of the failed fan slot to ensure the fault indicator is no longer lit.

This is necessary to ensure the indicator status is cleared before you insert the new fan. See

“Fan Module Reference” on page 135

for fan module indicator locations.

Orient the fan module so the connector on the bottom of the module is aligned

with the connector on the inside of the slot and all keying and labeling are

correctly positioned.

Servicing CRU Components

133

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды