Oracle X5-4 Скачать руководство пользователя страница 273

Страница: 273 / 358

BIOS Setup Utility Menu Options

This section describes the Basic Input/Output System (BIOS) Setup Utility.

Note -

For more information about BIOS, refer to the

Oracle X5 Series Servers Administration

Guide

http://www.oracle.com/goto/x86AdminDiag/docs

Description

Link

BIOS basics and screens

“About the BIOS Setup Utility” on page 273

BIOS screens

“Access the BIOS Setup Utility” on page 338

About the BIOS Setup Utility

The server's Basic Input/Output System (BIOS) is stored on the motherboard and managed

using the BIOS setup utility. The utility reports system information and provides a graphical

user interface that allows you to change the server BIOS settings from the factory-configured

defaults.

The BIOS has two operational boot modes, Legacy and UEFI. Changing modes changes the

content of some utility screens. The legacy boot mode is the default.

For a listing of the BIOS Setup Utility menus, see

“Legacy Mode BIOS Setup Utility

Screens” on page 274

BIOS Setup Utility Screens

This section contains screen captures of the higher-level BIOS Setup Utility menus.

■

“Legacy Mode BIOS Setup Utility Screens” on page 274

BIOS Setup Utility Menu Options

273

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды