Oracle X5-4 Скачать руководство пользователя страница 56

Страница: 56 / 358

Troubleshooting Hardware Faults Using Oracle ILOM

installing a power supply, ensure that it is fully seated and engaged with its connector inside the

drive bay.

A properly installed PSU has its green AC OK indicator lit. A properly functioning PSU has its

green power (DC) OK indicator lit and its amber Service Action Required indicator off

Top Cover

The server top cover helps the cooling subsystem maintain pressure areas within the server.

The top cover also protects against damage to internal components and accidental exposure to

hazardous voltages. For these reasons, the server top cover is includes an interlock switch to

server power.

The interlock switch has two components. One component is mounted inside the server on

the housing for power supply, PS1, and includes a wire that plugs into the motherboard. The

other component is mounted on the underside of the top cover. When the cover is installed these

two components align, closing the switch and allowing power to the server. When the cover is

removed, the switch opens removing power from the server. If the cover is removed while the

server is powered on to full power mode, power to the server is

immediately

switched off.

Action

: If the server does not power on, check that switch is intact and properly aligned. Ensure

that the server top cover is in place and sits flat and snug on top of the server. Ensure that the

interlock switch components have not been damaged, removed, or misaligned.

Prevention

: After removing the top cover, take care that the cover does not get bent, or that

the component on the underside is not damaged. When servicing the server, take care that the

internally mounted interlock switch component does not get damaged or misaligned. Never

operate the server without the top cover installed.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды