Oracle X5-4 Скачать руководство пользователя страница 184

Страница: 184 / 358

Install a CPU Cover Plate

Cover plates are plastic inserts that attach to the CPU load plate and protect the pins of an

unoccupied CPU socket. Cover plates are used in a two-CPU server (for the unoccupied slots)

and on replacement motherboards. When replacing a motherboard, remove the covers and

install them on the failed board.

Before You Begin

■

“Remove a CPU Cover Plate (FRU)” on page 181

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For CPU designation information, see

“Component Designations” on page 73

Prepare the server for service.

See

“Prepare the Server for Cold Service” on page 94

Disengage the CPU load plate release levers by pushing them down and moving

them slightly toward the CPU socket and away from their retaining clips.

The levers are numbered with their required order of operation. The left-side lever (when

viewed from the front of the server) must be operated first.

Rotate the levers to the fully-open position.

Opening the second lever completes unlocking the load plate.

To open the load plate, lift the unhinged end to its fully-open position.

184

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды