Oracle X5-4 Скачать руководство пользователя страница 28

Страница: 28 / 358

Server Subsystems Overview

Cooling the Two-CPU Configuration

A two-CPU server configuration has fewer components than a fully loaded, four-CPU

configuration. To maximize cooling in a two-CPU configuration, an air baffle is installed

in the memory riser area. The air baffle directs the fan output across the four memory riser

cards and the two CPUs. For more information about the processor subsystem, see

“Processor

Subsystem” on page 22

Over-Temperature Issues

When the server cooling system is compromised by a hardware component failure or an airflow

blockage, the internal temperature of the server can increase and cause component failure.

To protect against over-temperature conditions, the server temperature and components are

monitored using sensors. If the reading from a sensor indicates a temperature outside of the

normal operating range of the component, or if a cooling subsystem-related component (such

as a fan module) fails, the server management software lights the server fault indicator for the

component and logs an event in the system event log (SEL). When a fault event occurs, address

the issue

immediately

For information about troubleshooting the server cooling subsystem, see

“Troubleshooting

System Cooling Issues” on page 52

Power Subsystem

The server is equipped with two 1030/2060 watt auto-ranging hot-swappable power supplies

that support a two CPU configuration at 110–127 VAC, or two or four CPU configuration at

200–240 VAC. The dual power supply configuration provides N+N redundancy.

The server supports the following power modes, server shutdowns, and resets.

Full Power Mode

When full power mode is applied, power is supplied to all the server components, the server

boots, and the operating system (OS) functions. Apply full power mode by pressing the Power

button on the server front panel when the server is in standby power mode. You can also apply

full power to the server from Oracle ILOM. Once the server is operating in full power mode,

the System OK and service processor (SP) indicators are on steady (see

“Server Boot Process

and Normal Operating State Indicators” on page 41

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды