Oracle X5-4 Скачать руководство пользователя страница 271

Страница: 271 / 358

Power On the Server

Power On the Server

If you removed power from the server during maintenance, use the following procedure to

reapply main power for all server components.

Verify that the power cords are connected to the server and that standby power

is on.

■

Shortly after AC power cords are plugged into the server, the SP OK indicator blinks as the

service processor boots.

■

The SP OK indicator is illuminated solid green when the service processor has successfully

booted.

■

After the service processor has booted, the System OK indicator on the front panel begins

flashing slowly, indicating that the host is in standby power mode.

Press and release the recessed Power button on the server front panel.

■

When full power is applied to the server, the System OK indicator begins to blink more

quickly as the system begins the boot process.

■

During the boot process, the server initiates a power-on self-test (POST) which might take

several minutes to complete.

■

Once the host boot process is complete, the System OK indicator and lights solidly.

Callout

Description

System OK indicator

Power Button

SP OK indicator

Returning the Server to Operation

271

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды