Oracle X5-4 Скачать руководство пользователя страница 189

Страница: 189 / 358

Remove a Heatsink and CPU (FRU)

Remove the heatsink from the server.

Place the heatsink upside down on the work space.

Use an alcohol pad to clean the thermal compound from both the bottom of

the heatsink and the top of the CPU.

Caution -

Component damage. Failure to clean the thermal compound from the heatsink and

the CPU prior to removing the CPU could result in accidental contamination of the CPU socket,

the removal tool, or other components. Also, be careful not to get the grease on your fingers as

this could result in contamination of components.

To access the CPU, the CPU load plate needs to be opened. The load plate is locked in its

closed position by the load plate lever.

Servicing FRU Components

189

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды