Oracle X5-4 Скачать руководство пользователя страница 191

Страница: 191 / 358

Remove a Heatsink and CPU (FRU)

Note -

Ensure that you use the correct CPU replacement tool. The correct tool has part number

G29477-002 affixed to the side, and it has a green label. However, the label color alone is not

an indicator of the correct tool. Verify that the part number is correct.

Press down on the release button on top of the replacement tool.

This action opens the tool.
On one corner of the tool there is a label with a downward pointing triangle. Likewise,

the CPU is marked with a triangle on one of its corners. This is a key that aligns the tool

and the CPU with the CPU socket. The tool and the CPU are correctly positioned with the

socket when all of the triangles are aligned.

Orient the bottom of the tool over the CPU, ensuring that the triangle on the

tool aligns with the triangle on the CPU.

Lower the tool onto the CPU, ensuring that it sits evenly on the CPU.

Push the release tab away from the center button.

This action is accompanied by a click sound as the tool closes and grabs the CPU.

Servicing FRU Components

191

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды