Oracle X5-4 Скачать руководство пользователя страница 254

Страница: 254 / 358

Replace the Motherboard (FRU)

23.

Lower the motherboard into the server and carefully guide the light pipe

extension piece for the Locator indicator at the back of the motherboard into its

hole at the rear of the chassis.

Ensure that the switch operates easily and is not stuck in the depressed position.

24.

Ensure that the keyed holes in the plate attached to the underside of the

motherboard are aligned with the locking standoffs in the chassis.

25.

Slide the motherboard toward the back of the server. Ensure that motherboard

rear connectors fit completely into the holes provided in the chassis sheet metal.

This action locks the motherboard and aligns the captive screw on the motherboard plate

(towards the front of the server) with its thread hole in the chassis.

254

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды