Oracle X5-4 Скачать руководство пользователя страница 130

Страница: 130 / 358

Servicing Fan Modules (CRU)

Confirm that the drive has been enabled and is seen by the system.

Do one of the following:

■

Check the

/var/log/messages

log file.

■

List available NVMe devices. Type:
#

ls -l /dev/nvme*

Related Information

■

“Storage Drive Reference” on page 119

■

“Storage Drives Hot-Plug Conditions” on page 114

■

“Storage Drive Failure and RAID” on page 114

■

“DVD, Storage Drive, and USB Designations” on page 78

Servicing Fan Modules (CRU)

This section provides instructions for removing and installing a fan module.

■

“Remove a Fan Module” on page 130

■

“Install a Fan Module” on page 133

■

“Fan Module Reference” on page 135

Remove a Fan Module

Fan modules provide server cooling to the motherboard and its components. The fan modules

are arranged in stacked pairs (a front row and a back row) to provide redundancy. If you remove

a fan module, replace it immediately.

Fan modules are hot-serviceable components. It is not necessary to power off the server

or to remove the server cover to service a fan module. However, depending on server rack

configuration, it might be necessary to partially extend the server from the rack to access the

fan modules. (Optional steps for partially extending the server from the rack are included in

this procedure.) Take care when partially extending the server from the rack during hot service.

Ensure that the cables at the back of the server do not become dislodged, particularly the power

cables. As an option, you can also perform this procedure using cold service.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For fan module designation information, see

“Component Designations” on page 73

130

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды