manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 149

Remove a DIMM

Use this procedure to remove a DIMM from its slot on the memory riser (MR) card.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

■

For DIMM designation information, see 

“Component Designations” on page 73

.

■

For reference information, see 

“Memory Riser Card and DIMM Reference” on page 154

1.

If necessary, identify the faulty DIMM.

See 

“Identify a Faulty DIMM” on page 146

.

2.

To remove the DIMM do the following:

a.   

Rotate both DIMM slot ejector levers outward as far as they will go.

The action unlocks the DIMM and expels it from the socket.

b.   

Carefully lift the DIMM straight up to remove it from the socket.

3.

Repeat the above steps until all faulty DIMMs are removed.

Next Steps

“Install a DIMM” on page 150

Servicing CRU Components

149

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды