Oracle X5-4 Скачать руководство пользователя страница 40

Страница: 40 / 358

Troubleshooting Hardware Faults Using Oracle ILOM

To get more information, click one of the Open Problems links.

The Open Problems screen provides detailed information, such as the time the event occurred,

the component and subsystem name, and a description of the issue. It also includes a link to a

KnowledgeBase article.

Tip -

The System Log provides a chronological list of all the system events and faults that have

occurred since the log was last reset and includes additional information, such as severity levels

and error counts. The System Log also includes information on devices not reported in the

Subsystem Summary screen. To access it, click the System Log link.

In this example, the hardware fault with DIMM 8 of CPU 0 requires local/physical access to the

server.

Before going to the server, review the server

Product Notes

document for

information related to the issue or the component.

The

Product Notes

document contains up-to-date information about the server, including

hardware-related issues.

To prepare the server for service.

See

“Preparing to Service the Server” on page 93

Service the component.

Note -

After servicing the component, you might need to clear the fault in Oracle ILOM. For

more information, refer the component service procedure.

Troubleshooting Using the Front Panel Indicators

This section describes the state of the server front panel indicators when the system components

are in a fault state.

The eight indicators on the server front panel show the state of the server. The following

sections describe the conditions of the front panel indicators for various server states:

Note -

For more information about the server front panel, see

“Server Front Panel

Features” on page 17

■

“Server Boot Process and Normal Operating State Indicators” on page 41

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды