Oracle X5-4 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 358

background image

Prepare an NVMe Storage Drive for Removal

This section provides instructions for how to remove and replace an NVMe storage drive on a

server that is running the Oracle Linux operating system.

■

“Prepare an NVMe Storage Drive for Removal” on page 126

■

“Remove an NVMe Storage Drive From the Server” on page 128

■

“Verify Removal of an NVMe Storage Drive” on page 128

■

“Install an NVMe Storage Drive In the Server” on page 129

■

“Power On an NVMe Storage Drive” on page 129

Prepare an NVMe Storage Drive for Removal

Before You Begin

■

Linux NVMe hot plug requires the kernel boot argument "pci=pcie_bus_perf" be set in

order to get proper MPS (MaxPayloadSize) and MRR (MaxReadRequest). Fatal errors will

occur without this argument.

■

For a list of the virtual PCIe slots of NVMe drives as seen by the operating system, see

“NVMe Storage Drive Virtual PCIe Slot Designation” on page 115

. Note that the virtual

PCIe slot name is not the same as the name on the server front panel label.

1.

Log in to Oracle Linux that is running on the server.

2.

Obtain information about available NVMe storage devices.

a.

Obtain the PCIe addresses (Bus Device Function) of enabled NVMe drives.

Type:

#

find /sys/devices |egrep 'nvme[0-9][0-9]?$'

This commands returns output similar to the following:

/sys/devices/pci0000:00/0000:00:02.2/0000:10:00.0/0000:11:04.0/0000:12:00.0/misc/
nvme0
/sys/devices/pci0000:00/0000:00:02.2/0000:10:00.0/0000:11:05.0/0000:13:00.0/misc/
nvme1
/sys/devices/pci0000:00/0000:00:02.2/0000:10:00.0/0000:11:06.0/0000:14:00.0/misc/
nvme2
/sys/devices/pci0000:00/0000:00:02.2/0000:10:00.0/0000:11:07.0/0000:15:00.0/misc/
nvme3

For example,

0000:12:00.0

matches the PCIe address of the drive labeled NVMe0 on the

system front panel.

b.

Obtain the PCIe virtual slot number (APIC ID). Type:

#

egrep -H '.*' /sys/bus/pci/slots/*/address

126

Oracle Server X5-4 Service Manual • December 2015

«
...
124
125
126
127
128
...
»

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X5-4

Бренд: TANDBERG Страницы: 127

Бренд: F5 Страницы: 2

WANJet 400 Appliance

Бренд: F5 Страницы: 11

Бренд: Kathrein Страницы: 16

Бренд: MSI Страницы: 106

Бренд: Vxl Страницы: 2

Бренд: Sun Microsystems Страницы: 12

Express5800/R320f-E4

Бренд: NEC Страницы: 88

Бренд: Asus Страницы: 78

Бренд: Asus Страницы: 32

Aaeon AIOT-ILRA01

Бренд: Asus Страницы: 39

Бренд: Asus Страницы: 132

Бренд: Asus Страницы: 60

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 40

Бренд: Asus Страницы: 54

90SV045A-M05CE0

Бренд: Asus Страницы: 168

Бренд: Asus Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды