Oracle X5-4 Скачать руководство пользователя страница 265

Страница: 265 / 358

(Optional) Install the Server Into the Rack

The server should be flush with the front of the rack.

Verify that the server is securely mounted in the rack and that the slide-rail locks

are engaged with the mounting brackets.

At the rear of the server, connect the AC power cables to the server power

supplies.

When the power cables are connected to the server, the server powers on to standby power

mode.

Connect any other cables to their connectors or ports on the back of the server.

If the cable management arm (CMA) is in the way, disconnect the left CMA release and swing

the CMA open.

If necessary, reconnect the CMA.

See

“(Optional) Install Cable Management Arm” on page 266

Swing the CMA closed and latch it to the left rack rail.

10.

Power on the server.

Returning the Server to Operation

265

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды