Oracle X5-4 Скачать руководство пользователя страница 86

Страница: 86 / 358

Locate a Failed Memory Riser Card, DIMM, or CPU

Callout

Description

Callout

Description

MR card Fault indicator

Fault Remind button

DIMM Fault indicators

Charge Status indicator

†

The indicator lights when the circuit is charged.

Locate a Failed Memory Riser Card, DIMM, or CPU

To locate a failed memory riser card, DIMM or CPU, use the fault remind circuits inside the

server. The circuit uses board-mounted indicators to identify the failed component. If the failed

component is a memory riser card or a CPU, the indicators identify the component directly. If

the failed component is a DIMM, the indicators identify the memory riser card containing the

DIMM. Then to locate the failed DIMM, you need to remove the memory riser card and use the

card's DIMM Fault Remind circuitry.

For more information about the system and DIMM Fault Remind circuits, see

“Troubleshooting

Using the Fault Remind Test Circuits” on page 51

Before You Begin

To troubleshoot faulty hardware components, see

“Troubleshooting Server Hardware

Component Faults” on page 37

Note -

The test circuits are charged, time-limited circuits. Once power is removed from the

server you have 10 minutes to use the DIMM Fault Remind circuit and 30-60 minutes to use the

System Fault Remind circuit.

Prepare for service.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды