manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 35

Server Subsystems Overview

With Oracle System Assistant, you can:

■

Get a single server-specific bundle of the latest available BIOS, Oracle ILOM, and

hardware firmware and the latest tools and OS drivers from the Oracle support site.

■

Update OS drivers and component firmware and configure RAID.

■

Install supported operating systems with the latest drivers and supported tools.

■

Configure a subset of Oracle ILOM settings.

■

Save and restore customized BIOS settings or revert the BIOS to the factory defaults.

■

Access embedded product documentation.

■

Display system overview and detailed hardware inventory information.

Oracle Hardware Management Pack

Oracle Hardware Management Pack provides scriptable command-line tools that help you

manage and configure your Oracle servers from the host operating system.

Hardware Management Pack enables you to do the following using command-line tools:

■

Configure BIOS (Legacy and UEFI), RAID volumes, and Oracle Integrated Lights Out

Manager (ILOM).

■

Upgrade server component firmware.

■

Access the service processor and perform management tasks using IPMItool.

■

View hardware configuration information and the status of your Oracle servers.

■

Enable in-band monitoring of your Oracle hardware over Simple Network Management

Protocol (SNMP). You can use this information to integrate your Oracle servers into your

data center management infrastructure.

■

Set up an Oracle ILOM trap proxy that forwards SNMP traps from your Oracle ILOM

service processor to the host OS.

Oracle Server X5-4 Overview

35

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды