Oracle X5-4 Скачать руководство пользователя страница 64

Страница: 64 / 358

Reset the Host or SP Using Oracle ILOM

■

“Reset the Host or SP Using Oracle ILOM” on page 64

■

“Reset the Host or SP Using Back Panel Pinhole Switches” on page 64

■

“Reset the SP Root Account Password or Recover the Root Account” on page 65

Reset the Host or SP Using Oracle ILOM

Before You Begin

The Host Control and Reset (r) role is required to reset a service processor.

Log in to the Oracle ILOM (web or CLI) for the server.

Reset Oracle ILOM using one of the following methods:

■

From the Oracle ILOM CLI, enter the command:

reset /SP

■

From the Oracle ILOM web interface, click ILOM Administration >

Maintenance > Reset SP.

Note -

Resetting the Oracle ILOM SP disconnects your current Oracle ILOM session. You must

Reset the host using one of the following methods:

■

From the Oracle ILOM CLI, enter the command:

reset /System

■

From the Oracle ILOM web interface, click Host Management > Power

Control, then select your reset method from the drop-down list.

Reset the Host or SP Using Back Panel Pinhole

Switches

This section shows the location of the back panel pinhole switches.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Бренды по названию

Популярные бренды