manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 52

Troubleshooting Hardware Faults Using Oracle ILOM

Once AC power is connected to the system (providing standby power), the System Fault

Remind circuit energy storage capacitor takes about 10 minutes to charge to 63% (which should

be sufficient to turn on the indicator) and about 20 minutes to be fully charged. When you push

down on the Fault Remind button, its power indicator should show green when the circuit has

enough power to identify faulted components.

For information about how to use the circuits to identify failed components, see 

“Locate a

Failed Memory Riser Card, DIMM, or CPU” on page 86

.

Troubleshooting System Cooling Issues

Maintaining the proper internal operating temperature of the server is crucial to a the health of

the server. To prevent server shutdown and damage to components, address over temperature-

and hardware-related issues as soon as they occur. If your server has a temperature-related fault,

the cause of the problem might be one of following:

■

“External Ambient Temperature Too High” on page 52

■

“Airflow Blockage” on page 53

■

“Internal Pressures Compromised” on page 53

■

“Hardware Component Failure” on page 53

External Ambient Temperature Too High

Server component cooling relies on the movement of cool ambient air pulled into the server

from its external environment. If the ambient temperature of the server's external environment

is too high, cooling does not occur, and the internal temperature of server and its components

increases. This can cause poor server performance or a failure of one or more components.

Action

: Check the ambient temperature of the server space against the environmental

specifications for the server (see the 

Installation Guide

). If the temperature is not within the

required operating range, remedy the situation immediately.

Prevention

: Periodically check the ambient temperature of the server space to ensure that it

is within the required range, especially if you have made any changes to the server space (for

example, added additional servers). The temperature must be consistent and stable.

52

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды