manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 180

Servicing Processors and Heatsinks (FRU)

Servicing Processors and Heatsinks (FRU)

This section provides procedures for removing and installing CPUs and heatsinks.

For processor overview information, see 

“Processor Subsystem” on page 22

. For serviceability

information related to this component, see 

“Component Serviceability, Locations, and

Designations” on page 69

.

■

“Replace a Faulty CPU (FRU)” on page 180

■

“Remove a CPU Cover Plate (FRU)” on page 181

■

“Remove a Heatsink and CPU (FRU)” on page 186

■

“Install a Heatsink and CPU (FRU)” on page 193

Replace a Faulty CPU (FRU)

Disconnect the server from the AC power and protect components from ESD by wearing an

antistatic wrist strap.

For processor overview information, see 

“Processor Subsystem” on page 22

.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

■

For CPU designation information, see 

“Component Designations” on page 73

.

1.

Remove the heatsink and CPU.

See 

“Remove a Heatsink and CPU (FRU)” on page 186

.

2.

Install the CPU and the heatsink.

See 

“Install a Heatsink and CPU (FRU)” on page 193

.

180

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды