manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 11

Using This Documentation

This section describes how to get the latest firmware and software for the system,

documentation and feedback, and a document change history.

■

“Oracle Server X5-4 Model Naming Convention” on page 11

■

“Getting the Latest Firmware and Software” on page 11

■

“Documentation and Feedback” on page 12

■

“About This Documentation” on page 12

■

“Contributors” on page 12

■

“Change History” on page 12

Oracle Server X5-4 Model Naming Convention

The Oracle Server X5-4 name identifies the following:

■

X identifies an x86 product.

■

The first number, 5, identifies the generation of the server.

■

The second number, 4, identifies the number of processor sockets in the server.

Getting the Latest Firmware and Software

Firmware, drivers, and other hardware-related software for each Oracle x86 server are updated

periodically.

You can obtain the latest version in the following ways:

■

Oracle System Assistant: A factory-installed option for Oracle x86 servers. It has all the

tools and drivers you need and resides on an internal USB flash stick.

■

My Oracle Support: The Oracle support web site located at 

https://support.oracle.com

.

Using This Documentation

11

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды