manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 124

Install an NVMe Storage Drive in the Server

pcie101              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@5
pcie102              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@6
pcie103              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@7

Install an NVMe Storage Drive in the Server

Perform this procedure to physically install an NVMe storage drive into the server.

Note - 

After you physically remove an NVMe storage drive from the server, wait at least 10

seconds before installing a replacement drive.

1.

Remove the replacement drive from its packaging and place the drive on an

antistatic mat.

2.

If necessary, remove the drive filler panel.

3.

Align the replacement drive with the drive slot.

The drive is physically addressed according to the slot in which it is installed. It is important to

install a replacement drive in the same slot as the drive that was removed.

4.

Slide the drive into the slot until the drive is fully seated.

See 

“Install a Storage Drive (CRU)” on page 118

.

5.

Close the drive latch to lock the drive in place.

Power On an NVMe Storage Drive

Before You Begin

■

To perform this task, the hotplug daemon must be enabled on the host.

■

For a list of the virtual PCIe slots of NVMe drives as seen by the operating system, see

“NVMe Storage Drive Virtual PCIe Slot Designation” on page 115

. Note that the virtual

PCIe slot name is not the same as the name on the server front panel label.

1.

Power on the slot for the drive. Type:

# 

hotplug enable pcie100

In this example, 

pcie100

 is the drive labeled NVMe0 on the server front panel.

124

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды