manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 155

Install a Memory Riser Card

Callout

Description

Callout

Description

2

DIMM slots (12)

6

Charge status indicator (green)

3

Fault Remind button

7

Memory riser card fault indicator

4

DIMM fault indicators

 

 

Memory Riser Cards Physical Layout

The memory riser cards are located behind the fan module bay. The designations each memory

riser (MR) card and its associated CPU are located inside the server on labels affixed to the rear

MR card bracket. The cards are designated as MR, and the CPUs are designated as P. The slots

and CPUs are labeled from right to left when viewed from the front of the server as follows:

Note - 

Each CPU has two assigned card slots (MR0 and MR1).

■

P0/MR0 (rightmost slot)

■

P0/MR1

■

P1/MR0

■

P1/MR1

■

P2/MR0

■

P2/MR1

■

P3/MR0

■

P3/MR1 (leftmost slot)

The following illustration shows the numbering for the memory riser slots and their associated

CPUs as described above:

Servicing CRU Components

155

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды