manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 243

Servicing the SP Card (FRU)

d.   

Then, slide the divider downward to lock the tabs in the slots and secure it

against the wall.

To ensure proper alignment of the Fault Remind switch, both tabs 

must

 be engaged with

their slots.

17.

Reconnect the SAS and any NVMe cables to the disk backplane.

See 

“Replace the SAS 12 Gb/s Internal HBA SAS Cables (FRU)” on page 204

 and 

“Replace

the NVMe Switch Card Cables (FRU)” on page 215

.

18.

Reconnect the ESM cable to the ESM.

See 

“Replace the SAS 12 Gb/s Internal HBA ESM Cable (FRU)” on page 209

.

Or, if you removed the ESM, reattach it to the dual lock strip on the chassis.

19.

Install all disk drives and filler panels.

See 

“Install a Storage Drive (CRU)” on page 118

.

20.

Install the DVD drive.

See 

“Install the DVD Drive or DVD Drive Filler Panel” on page 170

.

21.

Prepare the server for operation.

See 

“Prepare the Server for Operation” on page 259

.

Note - 

The product serial number used for service entitlement and warranty coverage might

need to be reprogrammed by authorized service personnel with the correct product serial

number.

Servicing the SP Card (FRU)

This section provices procedures for removing and installing the motherboard-mounted service

processor (SP) card.

The replaceable SP card contains the embedded server management software, Oracle ILOM.

■

“Remove the SP Card (FRU)” on page 244

■

“Install the SP Card (FRU)” on page 245

Servicing FRU Components

243

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды