manualshive.com logo in svg

Oracle X5-4, Руководство по обслуживанию

Поделиться
Скачать
Oracle X5-4 Скачать руководство пользователя страница 93

Preparing to Service the Server

This section provides procedures for preparing the server for service.

Description

Links

Procedural information for preparing to

perform 

hot

 service on the server.

“Prepare the Server for Hot Service” on page 93

Procedural information for preparing to

perform 

cold

 service on the server.

“Prepare the Server for Cold Service” on page 94

Procedural information for releasing the

Cable Management Arm (CMA)

“Release the CMA” on page 98

Procedural information for server power-off

options.

“Powering Off the server” on page 101

Procedural information for using the Locator

indicator.

“Managing the Locator Indicator” on page 107

Procedural information for the server cover.

“Remove the Server Cover” on page 110

Prepare the Server for Hot Service

The following hot-service components can be removed and replaced while the server is

operating in full power mode:

■

Storage drives

■

Fan modules

■

Power supplies

For more information about component serviceability, see 

“Component

Serviceability” on page 70

.

Before You Begin

■

Important

: Review the server 

Product Notes

 document before performing removal and

installation procedures.

■

For troubleshooting information, see 

“Troubleshooting and Diagnostics” on page 37

.

Preparing to Service the Server

93

Содержание X5-4







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды