Oracle X5-4 Скачать руководство пользователя страница 65

Страница: 65 / 358

Reset the SP Root Account Password or Recover the Root Account

Callout

Description

SP Reset

Host Warm Reset

NMI (Oracle Service use only)

Reset the SP Root Account Password or Recover

the Root Account

If necessary, system administrators can recover the Oracle ILOM root account (if accidentally

deleted) or reset the password for the Oracle ILOM root account to the factory default

password.

To perform either action, you need a local serial management port (SER MGT) connection

to Oracle ILOM. In addition, if the Physical Presence State is enabled (the default) in Oracle

ILOM, you must prove that you are physically present at the server as described in the

following procedure.

To recover the root account or root account password, perform these steps:

Establish a local serial management connection to Oracle ILOM and log in to

Oracle ILOM using the default user account.

For example:

ORACLESP-000000000 login:

default

Press and release the physical presence button

Troubleshooting and Diagnostics

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды