Oracle X5-4 Скачать руководство пользователя страница 95

Страница: 95 / 358

Prepare the Server for Cold Service

■

Remove, replace, or install cold-serviceable components

■

Remove, replace, or install internal components

■

Use the motherboard processor and DIMM fault remind circuitry

Before You Begin

■

Important

: Review the server

Product Notes

document before performing removal and

installation procedures.

■

For troubleshooting information, see

“Troubleshooting Server Hardware Component

Faults” on page 37

To power down the server and activate the front panel Locator indicator, do the

following:

Log in to the Oracle ILOM web interface.

Type the server SP IP address into a web browser and log in as a user with root or

administrator privileges. For more information, refer to the

Oracle X5 Series Servers

Administration Guide

http://www.oracle.com/goto/x86AdminDiag/docs

In the Actions section of the Summary screen, click the Power State Turn Off

button.

This action powers off the server to standby power mode. For more power off options, see

“Powering Off the server” on page 101

In the Actions section of the Summary screen, click the Locator Indicator

Turn On button.

This action activates the Locator indicator on the server front panel. For more Locator

indicator management options, see

“Managing the Locator Indicator” on page 107

Preparing to Service the Server

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды