Oracle X5-4 Скачать руководство пользователя страница 253

Страница: 253 / 358

Replace the Motherboard (FRU)

Note -

If the Locator indicator light pipe extension detaches during removal, ensure that you

retrieve it from the server. The extension is a clear plastic piece that transmits light and allows

you to activate the Locator indicator switch from the back of the server. It is needed for the

replacement motherboard.

20.

To remove the motherboard, slowly guide it up and out of the server.

21.

Lift the replacement motherboard by the memory riser card guide and the handle

above the SP card slot.

Note -

Ensure that the removable light pipe extension piece for the Locator indicator is attached

to the indicator switch. The extension is a clear plastic piece that transmits light and allows you

to activate the Locator switch from the back of the server.

22.

Align the motherboard over the server with the memory riser card slots toward

the front.

Servicing FRU Components

253

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды