Oracle X5-4 Скачать руководство пользователя страница 152

Страница: 152 / 358

Install a Memory Riser Card

Install a Memory Riser Card

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Use this procedure to install a memory riser (MR) card into its slot.

Before You Begin

■

For serviceability considerations, see

“Component Serviceability” on page 70

■

For DIMM designation information, see

“Component Designations” on page 73

■

For reference information, see

“Memory Riser Card and DIMM Reference” on page 154

Ensure that all populated and unpopulated DIMM slot ejector levers are in the

closed and locked position.

Caution -

Component damage. Open DIMM ejector levers can break off during the installation

of the memory riser (MR) card. All populated and unpopulated DIMM slot ejector levers on the

MR card must be in the fully-closed and locked position before installing the card in the server.

Install the MR card as follows:

Ensure that the MR card ejector levers are in the closed position.

The ejector levers are only used to remove a MR card and are

not

used to install a card.

See the illustration below.

Align the MR card with its slot on the motherboard.

The DIMMs on the card must face the left (when looked at from the front of the server).

Carefully lower the card on to the slot.

Ensure that the card is in the provided card guide channels. See the illustration below.

152

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды