Oracle X5-4 Скачать руководство пользователя страница 57

Страница: 57 / 358

Troubleshooting With Diagnostic Tools

Troubleshooting With Diagnostic Tools

This section describes the available diagnostic tools and documentation that you can use to

troubleshoot server issues.

■

“Diagnostic Tools” on page 57

■

“Diagnostic Tool Documentation” on page 58

Diagnostic Tools

The server and its accompanying software and firmware contain diagnostic tools and features

that can help you isolate component problems, monitor the status of a functioning system,

and exercise one or more subsystems to disclose more subtle or intermittent hardware-related

problems.

Each diagnostic tool has its own specific strength and application. Review the tools listed in

this section and determine which tool might be best to use for your situation. Once you have

determined the tool to use, you can access it locally (while at the server) or remotely.

The selection of diagnostic tools available for your server range in complexity from a

comprehensive validation test suite (Oracle VTS) to a chronological event log (Oracle ILOM

System Log). The selection of diagnostic tools also include standalone software packages,

firmware-based tests, and hardware-based LED indicators.

The following table summarizes the diagnostic tools that you can use when troubleshooting or

monitoring your server.

Diagnostic

Tool

Type

What It Does

Accessibility

Remote Capability

Oracle

ILOM

firmware

Monitors environmental

conditions and component

functionality sensors,

generates alerts, performs

fault isolation, and

provides remote access.

Can function on either

standby power mode or

full power mode and is not

OS dependent.

Designed for remote and local

access.

Preboot

firmware

Enables you to restore

some Oracle ILOM default

settings when Oracle

ILOM is not accessible.

Can function on standby

power and when operating

system is not running.

Local, but remote serial access

is possible if the SP serial port

is connected to a network-

accessible terminal server.

Troubleshooting and Diagnostics

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды