![background image](http://html1.mh-extra.com/html/omron/nj501-1300/nj501-1300_user-manual_742205380.webp)
11 Troubleshooting
11-34
NJ-series CPU Unit Motion Control User’s Manual (W507)
Event name
Homing Direction Limit Input Detected
Event code
74250000 hex
Meaning
The limit signal in the homing direction was detected during a homing operation.
Source
Motion Control Function Module
Source details
Axis
Detection
timing
During instruc-
tion execution
Error attributes
Level
Minor fault
Recovery
Error reset
Log category
System
Effects
User program
Continues.
Operation
The axis stops with the stop method for the homing execu-
tion status.
System-defined
variables
Variable
Data type
Name
_MC_AX[*].MFaultLvl.Active
BOOL
Axis Minor Fault Occurrence
Cause and
correction
Assumed cause
Correction
Prevention
The Operation Selection at Negative
Limit Input or Operation Selection at
Positive Limit Input parameter is set to
No reverse turn
.
To prevent errors at the limit inputs,
set the Operation Selection at Nega-
tive Limit Input and Operation Selec-
tion at Positive Limit Input parameters
to
Reverse turn
.
Check to see if any of the conditions
that are given as causes exist in
advance.
The location of the homing input sig-
nal sensors, homing settings, and
homing start position cause a limit
input to be reached.
Correct the location of the input signal
sensors, homing settings, and homing
start position so that a limit input is
not reached.
The input signal sensor wiring is
incorrect or the sensor is faulty.
Correct the wiring of the input signal
sensor or replace the sensor.
Attached
information
None
Precautions/
Remarks
None
Event name
Homing Limit Inputs Detected in Both Directions
Event code
74260000 hex
Meaning
The limit signals in both directions were detected during a homing operation.
Source
Motion Control Function Module
Source details
Axis
Detection
timing
During instruc-
tion execution
Error attributes
Level
Minor fault
Recovery
Error reset
Log category
System
Effects
User program
Continues.
Operation
The axis stops with the stop method for the homing execu-
tion status.
System-defined
variables
Variable
Data type
Name
_MC_AX[*].MFaultLvl.Active
BOOL
Axis Minor Fault Occurrence
Cause and
correction
Assumed cause
Correction
Prevention
The wiring of the limit signal is incor-
rect.
Correct the wiring of the limit signal.
Check to see if any of the conditions
that are given as causes exist in
advance.
The limit sensor is installed in the
wrong location.
Correct the installation locations of
the limit sensors so that they do not
turn ON at the same time.
The contact logic of the limit signal is
not correct.
Correct the contact logic (N.C./N.O.)
of the limit signal.
The limit sensor failed.
Replace the limit sensor.
Attached
information
None
Precautions/
Remarks
None
Содержание NJ501-1300
