2
Unpack the equipment and verify
package content
Confirm that you have the following tools and cables:
• Phillips #2 screwdriver
• RJ-45 console port cable
•
ESD cable
Virtual Services Platform
8000 Series
Quick Install Guide
Avaya
1.
Avaya Virtual Services Platform (VSP) 8000 Series switch
2.
Rack-mounting hardware that includes:
a. Rack-mount brackets
b. Screws to attach brackets to the switch
c. Screws to attach the switch to the equipment rack
3.
AC power cord or DC power supply wiring assembly
(
Note:
A power cord is not included with the “A” variants of the
switch.)
4.
Documentation that includes this poster, regulatory information,
how to locate software, and how to locate Release Notes.
1
Before you start
This poster provides information and instructions to install
and commission a factory-supplied Avaya Virtual Services
Platform 8000 switch. You can download all documents
referenced in this guide at www.avaya.com/support.
Note:
Observe ESD precautions when unpacking.
Optionally order a redundant PSU to provide redundancy and
load sharing.
VSP 8200 and VSP 8400 AC power specifications:
3
Verify power supply unit (PSU)
specifications
VSP 8000
models
Primary
PSU
Redundant PSU
(to be ordered if required)
VSP 8284XSQ-AC
(ships with one AC PSU – order
code: EC8200?01-E6)
VSP 8284XSQ-AC No PC GSA
(ships with one AC PSU but no
power cord – order code:
EC8200A01-E6GS)
VSP 8284XSQ-AC NA PC GSA
(ships with one AC PSU and a
North American power cord –
order code: EC8200E01-E6GS)
VSP 8404
(ships with one AC PSU but no
power cord —
order code:
EC8400A01-E6)
VSP 8404
(for government systems)
(ships with one AC PSU but no
power cord — order
code:
EC8400A01-E6GS)
VSP 8404C-AC
(ships with one AC PSU
– order code: EC8400?02-E6)
VSP 8404C-AC NA PC GSA
(ships with one AC PSU
and a North American
power cord – order
code: EC8400E02-E6GS)
VSP 8404C-AC No PC GSA
(for government systems)
(ships with one AC PSU
but no power cord —
order code: EC8400A02-E6GS)
800-W AC
power supply
(replacement
order code:
EC8005?01-E6)
800-W AC power supply
(order code: EC8005?01-E6)
Note:
The seventh character (?) of the
switch order number must be replaced
with the proper letter to indicate desired
product nationalization.
•
“A”:
No power cord included.
•
“B”:
Includes European
“Schuko” power cord common
in Austria, Belgium, Finland,
France, Germany,
The Netherlands, Norway,
and Sweden.
•
“C”:
Includes power cord
commonly used in the United
Kingdom and Ireland.
•
“D”:
Includes power cord
commonly used in Japan.
•
“E”:
Includes North American
power cord.
•
“F”:
Includes Australian
power cord.
The VSP 8000 Series supports two field-replaceable 800-W
power supplies. One power supply ships with the unit and you
can optionally install a second power supply for redundancy.
If you install a second power supply, the load is shared equally
and neither one acts as a primary power supply.
Use this procedure to install either the primary or redundant
power supply.
4
Install power supply unit
• There are two power supply slots (PSU1 on top and PSU2 on
the bottom). If you only have one power supply, you can install it
in either PSU1 or PSU2.
• The switch ships with filler panels covering the power supply
slots. If you’re not installing a second power supply, you must
leave one of the filler panels in place for proper cooling.
• You can hot swap power supplies while the switch is operational.
One power supply is required for continued
switch operation.
1.
Remove the two screws that secure the filler panel to the
chassis. (Save the filler panel for possible future use.)
2.
Insert the power supply into the slot.
3.
Verify that the power supply is fully seated in the slot (AC PSU
shown). The spring latch should engage and move back to its
original position as shown below:
Notes:
• The chassis design prevents an incorrect installation of a
power supply. If you insert a power supply upside down, it will
not fully insert.
• The spring latch design ensures that you remove the power
cord before removing a power supply from the chassis. If you
don’t remove the cord, you cannot move the latch to the left to
release the hooks from the chassis.
4. After you install a power supply, proceed with connecting either
the AC power cord or the DC power supply wiring assembly.
5.
Check the LED on the power supply. If it is off, the power supply
is not operating. If it is green, the power supply is operating
normally.
There are two ways to install an Avaya VSP 8000 switch in an
equipment rack. Refer to one of the following sections:
• Mount the switch using the supplied bracket.
• Mount the switch using the optional slide rack mount kit.
Note:
For more details on installing the VSP 8000 Series, see
Avaya VSP 8000 Series Installation (NN47200-300).
5
Mount the VSP 8000 switch
3.
Slide the switch onto a shelf in the rack as illustrated.
4.
Insert and tighten the rack-mount screws.
25
27
29
31
26
28
30
32
25
27
29
31
26
28
30
32
17
19
21
23
18
20
22
24
17
19
21
23
18
20
22
24
33
35
37
39
34
36
38
40
33
35
37
39
34
36
38
40
9
11
13
15
10
12
14
16
9
11
13
15
10
12
14
16
41
42
VSP 8284XSQ
41
42
USB
Console
PWR
Status
RPS
Fan
SLOT 1
SLOT 2
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
25
27
29
31
26
28
30
32
25
27
29
31
26
28
30
32
17
19
21
23
18
20
22
24
17
19
21
23
18
20
22
24
33
35
37
39
34
36
38
40
33
35
37
39
34
36
38
40
9
11
13
15
10
12
14
16
9
11
13
15
10
12
14
16
41
42
VSP 8284XSQ
41
42
USB
Console
PWR
Status
RPS
Fan
SLOT 1
SLOT 2
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
Prepare the rack
• Ensure that there is enough rack space to accommodate a
2RU switch (8.8 cm).
•
The rack is bolted to the floor and braced if necessary.
•
The rack is grounded to the same grounding electrode used
by the power service in the area. The ground path must be
permanent and must not exceed 1 Ohm of resistance from
the rack to the grounding electrode.
Mount the switch using the supplied bracket
Caution:
Avaya strongly recommends using the mounting
brackets with a shelf. Using the brackets without a shelf can
cause damage to the rack because of the chassis weight.
When you mount the device in a rack, do not stack units
directly on top of one another.
1.
Disconnect the power cord from the switch.
2.
Attach a bracket to each side of the switch as illustrated below.
• Use the front set of holes for a 4–post rack installation.
• Use the set of holes near the center of the chassis for a
2–post rack installation.
or
VSP 8200 and VSP 8400 DC power specifications:
VSP 8000
models
Primary
PSU
Redundant PSU
(to be ordered if required)
VSP 8284XSQ-DC
(ships with one DC PSU and a
DC power supply wiring
assemby – order code:
EC8200001-E6)
VSP 8404-DC
(ships with one DC PSU and a
DC power supply wiring
assembly — order code:
EC8400001-E6)
VSP 8404C-DC
(ships with one DC PSU and a
DC power supply wiring
assembly — order code:
EC8400002-E6)
800-W DC
power supply
(replacement order
code:
EC8005001-E6)
800-W DC power supply
(replacement order code:
EC8005001-E6)
Notes:
• Avaya does not support installing a combination of AC-input
and DC-input power supplies in the same chassis.
25
27
29
31
26
28
30
32
25
27
29
31
26
28
30
32
17
19
21
23
18
20
22
24
17
19
21
23
18
20
22
24
33
35
37
39
34
36
38
40
33
35
37
39
34
36
38
40
9
11
13
15
10
12
14
16
9
11
13
15
10
12
14
16
41
42
VSP 8284
XSQ
41
42
USB
IOIOI
PWR
Status
RPS
Fan
SLOT 1
SLOT 2
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
