INVT GD310-011P-4-UL, Руководство по эксплуатации

Страница: 155 / 269

GD310-UL series VFD Basic operation instruction
-147-
7.11 Digital input
Goodrive310-UL series VFDs have 8 programmable digital input terminals and 1 open circuit
electrode output terminal in the standard configuration. All functions of the digital input terminals are
programmable by the function codes. Open collector pole input can be selected into high speed pulse
input terminal or common switch input terminal by function code. When selected into HDI, the user
can select HDI high speed pulse input as frequency given, counting input or length pulse input by
setting.
S1
S2
S3
S4
S5
S6
S7
S8
HD1
P05.10
P05.01
P05.02
P05.03
P05.04
P05.05
P05.06
P05.07
P05.08
P05.09
T delay
T delay
T delay
T delay
T delay
T delay
T delay
T delay
T delay
P05.15
P05.17
P05.19
P05.21
P05.23
P05.25
P05.27
P05.29
P05.31
0
1
2
3
4
5
.
.
.
.
29
30
P05.11
(default value is 1)
(default value is 4)
(default value is 7)
(default value is 0)
(default value is 0)
(default value is 0)
(default value is 0)
(default value is 0)
(default value is 0)
P05.00
0
1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
0
1 -1
P17.12
Digital input
terminals state
0 No function 1 Forward running
4 Forward jogging 5 Reverse jogging
8 Running pause 9 External fault input
12
Frequency increasing/decreasing
setting clear
13
Shifting between A frequency and
B frequency
16 Multi-stage speed terminal 1 17 Multi-stage speed terminal 2
20 Multi-stage speed pause 21 ACC/DEC time selection 1
2 Reverse running
6
Coast to stop
10 Frequency setting increasing (UP)
14
Shifting between the combination
setting and A frequency
18 Multi-stage speed terminal 3
22 ACC/DEC time selection 2
23 Simple PLC pause 25 PID control pause
28 Counter reset 29 Torque control disabling
26
Traverse pause (stop at the current
frequency)
30 ACC/DEC disabling
32 Length reset 33
Frequency increasing/decreasing
setting clear
34 DC braking
3
3-wire running control
7
Fault reset
11 Frequency setting decreasing (DOWN)
15
Shifting between the combination setting
and B frequency
19 Multi-stage speed terminal 4
23 Simple PLC stopping reset
27
Traverse reset (stop at the middle
frequency)
31 Counter trigging
35 Shift from motor 1 to motor 2
36 Shift the command to the keypad 37 Shift the command to the terminal 38
Shift the command to the
communication
39 Pre-exciting command
40 Power consumption clear 41 Power consumption keeping 42~63 Reserved
P07.39
Input terminals
state at present
fault
Fault?
S1 BIT0 S2 BIT1
S3 BIT2 S4 BIT3
S5 BIT4 S6 BIT5
S7 BIT6 S8 BIT7
HDI BIT8
P05.10, P17.12, P07.39 display
P05.00
0: HDI is high speed pulse
input
1: HDI is switch input
Fault
Running
Switch function selection
T delay
T delay
T delay
T delay
T delay
T delay
T delay
T delay
T delay
P05.14
P05.16
P05.18
P05.20
P05.22
P05.24
P05.26
P05.28
P05.30
This parameter is used to set the function corresponds to the digital multi-function terminals.
Note : two different multi-function terminals cannot be set as one function.
Set
value
Function Instructions
0 No function
The VFD does not work even there is input signal. It is
necessary to set the terminal which cannot be used to
non-function to avoid misacting.
1
Forward running (FWD)
The forward or reverse rotation of the VFD can be controlled
by the external terminals.
2 Reverse running (REV)
3 3-wire running control
The terminal can determine the running mode of the VFD is
3-wire control mode. Refer to P05.13 for detailed instruction
of 3-wire control mode.