manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 73

Volume 1 / Print Engine - Error Codes & Messages

1

-

51

RAP 1-5

Error Code U3-3 

Laser Failure

Power Off/On

There is a problem with the Start of Scan (SOS) Sensor.

Logic Control on the Print Engine Controller Board detected that the time between signals 

from the Start of Scan Sensor was longer than specified.

Table 1-33 Error Code U3-3 Laser Failure Power Off/On

Step

Actions and Questions

Yes

No

1

RESET

Switch off printer main power.
Wait one minute.

Switch on printer main power.

Does the U3-3 error code appear?

Go to step 2

Suspect an 
intermittent 
problem with 
the Print 
Engine 
Controller 
Board, the 
Laser Diode 
board, the 
SOS Sensor, 
or the 
connectors 
and wiring 
linking these 
components.

2

LOW VOLTAGE POWER 5VDC 
CHECK

Measure the voltage between J400, pins 1, 2 & 3 (on the 
Print Engine Controller Board) and frame ground.

Is there +5VDC between J400, pins 1,2 & 3 and 
frame ground?

Go to step 3

Replace the 
Low Voltage 
Power Supply 
Assembly 
(RRP 1-67)

3

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 4

Problem 
solved

4

LASER SCANNER REPLACEMENT

Replace the Laser Scanner Assembly (RRP 1-47).

Does the error code appear?

Go to step 5

Problem 
solved

5

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands