manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 4

Power Supply and Electrical Components:  

Before starting any service 

procedure, switch off the printer power and unplug the power cord from the 

wall outlet. If you must service the printer with power applied, be aware of the 

potential for electrical shock.

Do not touch any electrical component unless you are instructed to do so by a 

service procedure.

Mechanical components:

  Manually rotate drive assemblies to inspect 

sprockets and gears.

Do not try to manually rotate or manually stop the drive assemblies while any 

printer motor is running

Laser Components

  

WARNING

:

This printer generates a laser beam as part of the printing process. 

The laser beam is a concentrated narrow beam of light that 

produces extreme heat at its focal point. The laser beam in this 

printer is invisible. Although you cannot see the beam, it can still 

cause severe damage. Direct eye exposure to the laser beam may 

cause eye injury or blindness.

To avoid permanent eye damage, follow these directions:

Before starting any service procedure, switch off the printer power and 

unplug the power cord from the AC wall outlet. 

Do not disassemble the Raster Output Scanner Assembly (laser 

scanner) or any laser component that displays a Laser Warning Sticker.

Use caution when you are working around the Raster Output Scanner 

Assembly or when you are performing laser related troubleshooting or 

repair procedures.

Never place a mirror or a reflective tool or object in the laser beam path.

Do not disassemble the printer in such a way that the laser beam can 

exit the print engine during a print cycle.

S4525-01

S4525-02

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands