manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 263

Volume 1 / Print Engine - FRU RRPs

1

-

241

Removal

1.

Remove the Fuser Assembly.

2.

Remove the Laser Print (EP) Cartridge.

3.

Remove the Offset Exit Unit Assembly (RRP 1-54).

4.

Disconnect J31, J32, and J33 from the AC Driver Board and free the wire 
harness from the harness clips.

5.

Disconnect J802 from High Voltage Power Supply-R2 and free the wire 
harness from the harness clips.

6.

Remove P204 wire harness from the Fuser Drive Assembly.

7.

Disconnect J104, J456 (on the Input/Output Board), J600, and J602.

8.

Remove the two screws (one black self-tapping and one black machine screw) 
securing the Fuser Drive Assembly to the printer frame, and lift the Assembly 
off of the frame.

9.

Remove the Input/Output Board and chassis sufficiently to swing out of the way 
and access the High Voltage Power Supply (RRP 1-70).

10.

Remove the High Voltage Power Supply sufficiently to access the machine 

screw attaching  the green wire (ground) termination.

11.

Remove the machine screw securing the green ground wire to the printer 

frame.

12.

Pull up and remove the Fuser Drive Assembly.

Replacement

1.

Reinstall the Fuser Drive Assembly onto the printer frame. (Refer to the figure 
for correct positioning)

2.

Align the Assembly so the screw holes and locating holes in the Assembly line 
up with the screw holes and locating tabs on the frame.

3.

Use two screws to secure the Assembly to the frame.

4.

Reinstall the green ground wire to the printer frame using the machine  screw 
(removed in Step 11 above) to secure the wire.

5.

Reinstall the High Voltage Power Supply.

6.

Reinstall the Input/Output Board and chassis.

7.

Reconnect J104, J456, J600, and J602.

8.

Reinstall P204 wire harness to the Fuser Drive Assembly.

9.

Reconnect J802 to High Voltage Power Supply-R2 and secure the wire 
harness under the harness clips.

10.

Reconnect J31, J32, and J33 to the AC Driver Board and secure the wire 

harness under the harness clips.

11.

Reinstall the Offset Unit Assembly (RRP 1-51).

12.

Reinstall the Laser Print (EP) Cartridge (RRP 1-45).

13.

Reinstall the Fuser Assembly (RRP1- 49).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands