manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 41

Volume 1 / Print Engine - General Information

1

-

19

Paper Input Devices

Trays 1 and 2 for the 500 Sheet Feeder (standard)

Standard feeder for the DocuPrint® N4525 Network Laser Printer.  Each tray has paper 
size automatic sensing.  Trays 1 and 2 can each hold up to 500 sheets (54 mm (2.126 in.) 

stack height of 20 lb. paper) of the following paper:

MBF (Multi-sheet Bypass Feeder - standard)

Standard feeder for the printer.  The MBF attaches to the left side of the printer.  The MBF 

holds up to 50 sheets (5 mm stack height of 64~105 g/m

2

 (17~28 Lb.) paper or 190 g/m

2

 

postcard) of the following paper:

Table 1-10 Tray 1 and 2 Paper Sizes

Factory set Option 1

Factory set Option 2

Ledger SEF - 279.4 mm x 431.8 mm (11 x 
17 in.)

Ledger SEF - 279.4 mm x 431.8 mm (11 x 17 in.)

A3 SEF - 297 mm x 420 mm (11.71 x 16.55 
in.)

A3 SEF - 297 mm x 420 mm  (11.71 x 16.55 in.)

B4 SEF - 257 mm x 364 mm (10.13 x 14.34) Legal 14" SEF - 215.9 mm x 355.6 mm (8.5 x 14 

in.)

Letter SEF LEF - 215.9 mm x 279.4 mm (8.5 
x 11 in.)

Letter SEF LEF - 215.9 mm x 279.4 mm (8.5 x 11 
in.)

Legal 13" SEF - 215.9 mm x 330.2 mm (8.5 x 
13 in.)

Legal 13" SEF - 215.9 mm x 330.2 mm (8.5 x 13 
in.)

A4 SEF LEF - 210 mm x 297 mm (8.27 x 
11.71 in.)

A4 SEF LEF - 210 mm x 297 mm (8.27 x 11.71 
in.)

Executive LEF - 184.2 mm x 266.7 mm (7.26 
x 10.51 in.)

B5 LEF - 182 mm x 257 mm (7.17 x 10.13)

A5 LEF - 149 mm x 210 mm (5.87 x 8.27 in.) A5 LEF - 149 mm x 210 mm (5.87 x 8.27 in.)

STATEMENT - 139.9 mm x 215.9 mm (5.51 
x 8.5 in.)

STATEMENT - 139.9 mm x 215.9 mm (5.51 x 8.5 
in.)

Table 1-11 Multi-sheet Bypass Feeder Paper Sizes

Factory set Option 1

Factory set Option 2

Ledger SEF - 279.4mm x 431.8 mm (11 x 17 
in.)

Ledger SEF - 279.4 mm x 431.8 mm (11 x 17 
in.)

A3 SEF - 297 mm x 420 mm (11.71 x 16.55 in.) A3 SEF - 297 mm x 420 mm  (11.71 x 16.55 

in.)

B4 SEF - 257 mm x 364 mm (10.13 x 14.34)

Legal 14" SEF - 215.9 mm x 355.6 mm (8.5 x 
14 in.)

Letter SEF LEF - 215.9 mm x 279.4 mm (8.5 x 
11 in.)

Letter SEF LEF - 215.9 mm x 279.4 mm (8.5 x 
11 in.)

Legal 13" SEF - 215.9 mm x 330.2 mm (8.5 x 
13 in.)

Legal 13" SEF - 215.9 mm x 330.2 mm (8.5 x 
13 in.)

A4 SEF LEF - 210 mm x 297 mm (8.27 x 11.71 
in.)

A4 SEF LEF - 210 mm x 297 mm (8.27 x 11.71 
in.)

Executive LEF - 184.2 mm x 266.7 mm (7.26 x 
10.51 in.)

B5 LEF - 182 mm x 257 mm (7.17 x 10.13 in.)

Postcard - 100 mm x 148 mm (3.94 x 5.83 in.)

Postcard - 100 mm x 148 mm (3.94 x 5.83 in.)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands