Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 282

Page: 282 / 380

1-260

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-70 Input/Output Board (PL 11.2)

Removal

Remove the Rear Cover (RRP 1-5).

Disconnect the eighteen P/Js (see Illustration) from the Input/Output Board.

Remove the four machine screws securing the Input/Output Board Bracket to
the printer frame and remove the Bracket.

Remove the six machine screws securing the Input/Output Board to the
Bracket and remove the board.

Fig 1-92 Input/Output Board

I/O Board

Bracket

(P450)

(P451)

(P467)

(P463)

(P464)

(P466)

(P127)

(P462)

(P461)

(P459)

(P465)

(P457)

(P452)

(P453)

(P460) (P456)

(P458)

(P454)

S4525-141

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands

Xerox DocuPrint N4525, Service Quick Reference Manual

Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands