manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 183

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

161

Press (3) or (7) to display 
“value”.
Continue pressing [3] or 
[7] to adjust “value”.

Value Up (3) / Value 

Down (7)

Adjustment Range

Line

No.

Press [1] or [5] 
to display: 

ß

Press [2] or [6] 
to display: 

ß

Press [4] to write to 
NVRAM, [0] to exit.

Min

Def

Max

31

NOTE - The following papers are applicable for 
the temperature settings:

TR1 & TM1

11 x 17 - SEF
A3 - SEF
A4 - LEF or SEF
8.5 x 11 - LEF or SEF
B4 - SEF
B5 - LEF
7.25 x 10.5 (Executive) - LEF
5.5 x 8.5 (Statement) - LEF
8.5 x 14 (Legal) - SEF

TR2

B5 - SEF

TM2

B5 - SEF
C6 - SEF
A5 - SEF
5.5 x 8.5 - SEF
A6 (Postcard) - SEF

TE1 & TE2

#10 - SEF
Monarch - LEF
DL - LEF
C5 - LEF

32

Main Menu
NVM Others Adj.

NVM Others Adj.
Trail Force Ers

Trail Force Ers
Each step value = .41 mm

0

54

97

Table 1-104 NVRAM Adjustment Table (cont'd.)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands