manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 285

Volume 1 / Print Engine - FRU RRPs

1

-

263

2.

Reinstall the Print Engine Controller Board onto the System Controller 
Assembly.  Align the board such that J406 faces the System Controller Board 
location.

3.

Reinstall the two 7mm nuts onto J406 and the six mounting screws (removed in 
step 6 above) loosely.  When all screws have been started, tighten them.

4.

Reconnect J400, J402, J403, J404, J408, J411 and the video plug (P409) into 
their respective connectors on the Print Engine Controller Board.

5.

Reinstall the System Controller Board, mating with J406 on the Print Engine 
Controller Board.

6.

Reconnect J400, J402, J403, J404, J408, J409 and J411 to the Print Engine 
Controller Board.

7.

Reinstall the System Controller Assembly Cover.

8.

Reinstall the Top Cover (RRP 1-2).

9.

Resintall the Fuser Cover (RRP 1-1).

Note

After Replacement,

 verify Lead and Side Edge Registration for all 

Bins.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands