manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 121

Volume 1 / Print Engine - Error Codes & Messages

1

-

99

RAP 1-44

Error Code J8-1 

Print Cartridge 

OEM ID 
Mismatch

The wrong Laser Print (EP) Cartridge is installed in the printer.

Logic Control on the Print Engine Controller Board sensed that the Laser Print (EP) 

Cartridge installed is not compatible with the printer.

Table 1-72 Error Code J8-1 Print Cartridge OEM ID Mismatch

Step

Actions and Questions

Yes

No

1

LASER PRINT (EP) CARTRIDGE 
REPLACEMENT

Replace the Laser Print (EP) Cartridge with a different 
one.

Does the error code still appear?

Go to step 2

Problem 
solved

2

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 3

Problem 
solved

3

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands