manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 136

1-114

DocuPrint N4525 Network Laser Printer - Service Guide

4

IMAGE TRANSFER INSPECTION

1. Carefully remove the Test Print generated in step 3.
2. Inspect the print.

Was the toner image on the drum transferred 
completely to the paper and are the grid lines 
black and unbroken?

Go to step 5

Replace the 
Bias Transfer 
Roller 
Assembly. If 
the problem 
persists, 
replace the 
High Voltage 
Power Supply 
Assembly.

5

FUSER INSPECTION

1. Generate another Grid Pattern Test Print and switch 

OFF printer power when the print is halfway through 
the Fuser.

2. Open the Left Upper Cover.
3. Examine the paper areas before the image enters the 

Fuser and after the image exits the Fuser.

Is the image normal before it enters the Fuser, 
but light when it exits the Fuser?

Replace the 
Fuser 
Assembly

Go to step 6

6

The following printer components and areas are 
associated with this specific problem. One or more of 
these components or areas may have failed partially or 
completely. If you cannot isolate this problem using the 
steps in this Fault Isolation Procedure, replace each 
component or troubleshoot each area listed below until 
you isolate and solve the problem.

Laser Scanner Assembly (RRP 1-47)

Print Engine Controller Board (RRP 1-72)

Input/Output Board (RRP 1-70).

Table 1-84 Light (Undertoned) Prints (cont'd.)

Step

Actions and Questions

Yes

No

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands