manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 156

1-134

DocuPrint N4525 Network Laser Printer - Service Guide

3

IMAGE TRANSFER INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Blank Test Print and switch OFF printer 

power halfway through the print cycle.

3. Open the Left Upper Door.
4. Open the Drum Shutter.
5. Hand rotate (counter clockwise) the Drum Drive Motor 

flywheel to advance the Drum far enough so you can 
see the developed image area on the Drum before it 
reached Transfer.

Before Transfer was the drum clean and 
without noticeable background toner, but there 
was background visible on the paper after 
Transfer?

Replace the 
Bias Transfer 
Roller 
Assembly

Go to step 4

4

FUSER INSPECTION

1. Generate another Blank Test Print and switch OFF 

printer power when the print is halfway through the 
Fuser.

2. Open the Left Upper Door.
3. Examine the paper before it enters the Fuser and after 

it exits the Fuser.

Is paper clean before it enters the Fuser, but 
there is background on the paper when it exits 
the Fuser?

Replace the 
Fuser 
Assembly

Go to step 5

5

The following printer components and areas are 
associated with this specific problem. One or more of 
these components or areas may have failed partially or 
completely. If you cannot isolate this problem using the 
steps in this Fault Isolation Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Replace the paper with another brand of paper

High Voltage Power Supply Assembly (RRP 

1-69)

Print Engine Controller Board (RRP 1-72)

Input/Output Board (RRP 1-70).

Table 1-94 Background (cont'd.)

Step

Actions and Questions

Yes

No

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands