manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 101

Volume 1 / Print Engine - Error Codes & Messages

1

-

79

RAP 1-28

Error Code E5-1  

Close Door A

The Left Door (A) is open.

The Left Door (A) is closed, but Logic Control on the Print Engine Controller Board 

sensed the Left Door (A) Interlock Switch indicates the door is open

Table 1-56 Error Code E5-1 Close Door A

Step

Actions and Questions

Yes

No

1

LEFT DOOR CHECK

Open and close the Left Door (A).

Does the error code appear?

Tighten the 
Switch 
Bracket screw 
(RRP 1-71) 

Go to step 2

2

LEFT DOOR INTERLOCK SWITCH 
INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Inspect the Left Door (A) Interlock Switch for damage, 

such as a broken or missing spring or a broken switch 
button.

Is the switch undamaged?

Go to step 3

Replace the 
Left Cover 
Interlock 
Switch (RRP 
1-71)

3

LEFT DOOR INTERLOCK ACTUATOR 
INSPECTION

Open and close the Left Door (A) while observing the 
action of the Left Door (A) Actuator against the Interlock 
Switch Spring.

Is the Left Cover Interlock Actuator pressing 
against the Interlock Switch Spring?

Go to step 4

Replace the 
Left Upper 
Cover (RRP 
1-42)

4

LEFT DOOR INTERLOCK SWITCH TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT 

Unit / L/H Cover A.

3. Press [4] to start, [0] to stop.
4. Actuate and deactuate the Left Door Interlock Switch.

Does the display indicate Open/Closed when 
you actuate and deactuate the Left Cover 
Interlock Switch?

Go to step 5

Replace the 
Left Cover 
Interlock 
Switch (RRP 
1-71)

5

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72.

Does the error code appear?

Go to step 6

Problem 
solved

6

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands