manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 281

Volume 1 / Print Engine - FRU RRPs

1

-

259

RRP 1-69 High Voltage Power Supply (PL 11.2)

Removal

1.

Remove the Input/Output Board (RRP 1-70).

2.

Disconnect J500, P701, P702 and BTR (Bias Transfer Roller) from the High 
Voltage Power Supply Board.

Caution

The board is easily broken. Use care when removing the P/Js from 

the High Voltage Power Supply Board. Use your fingers to hold 
down the board while you carefully disconnect each P/J.

3.

Remove the two machine screws, one on the left side and one on the right side, 
that secure the High Voltage Power Supply Assembly to the printer frame.

4.

Pull out on the High Voltage Power Supply Assembly while you release the two 
clips, one at the top and one on the right side, that secure the High Voltage 
Power Supply to the printer frame.

5.

Remove the High Voltage Power Supply Assembly from the frame.

Fig 1-91  High Voltage Power Supply

S4525-140

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands