manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 255

Volume 1 / Print Engine - FRU RRPs

1

-

233

Removal

1.

Remove the Rear Cover (RRP 1-5).

2.

Remove the Duplex Module, if installed.

3.

Open the Left Upper Cover.

Caution

When the Left Upper Cover is open, the Bias Transfer Roller is 

exposed. Do not touch the Bias Transfer Roller. Grease and dirt 
on the Bias Transfer Roller, or physical damage to the Bias 

Transfer Roller will affect print quality.

4.

Use a small screwdriver blade to release the latch securing the Front Shaft 
Hinge Pin, and slide it out of the Cover Assembly.  

Caution

Remove this smaller Hinge Pin to prevent it from falling into the 
printer and causing damage, or to prevent it from falling out and 

getting lost.

5.

Use a small screwdriver blade to release the latch securing the Rear Shaft 
Hinge Pin, and slide it out of the Cover Assembly.  

6.

Pull the Left Upper Cover Assembly away from the printer frame.

7.

Remove the two black self-tapping screws securing the two Cover Supports to 
the frame, and remove the Cover.  See illustration.

Replacement

1.

Open the Duplex Module.

Caution

When the Left Upper Cover is open, the Bias Transfer Roller is 
exposed. Do not touch the Bias Transfer Roller. Grease and dirt 

on the Bias Transfer Roller, or physical damage to the Bias 
Transfer Roller will effect print quality.

2.

Reinstall the Left Upper Cover Assembly so the hinge openings in the Cover 
arms line up with the hinge holes in the printer frame.

3.

Slide the Rear Shaft Hinge into the hinge opening in the Rear Cover arm, until 
the latch locks the Hinge onto the shaft.

4.

Slide the Front Shaft Hinge into the hinge opening in the Front Cover arm, until 
the latch locks the Hinge onto the shaft.

5.

Use the two black self-tapping screws to secure the two Cover Supports to the 
frame.

6.

Reinstall the Rear Cover (RRP 1-5).

7.

Open and close the Cover to make sure it opens and latches correctly.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands